Ceramic - 8 Pin Octal Tube Socket (solder)

Ceramic Tube socket used for octal power tubes. Chassis hole: 1” to 1-1/4” depending on mounting (Top: 1” to 1-1/16”, Bottom: 1-1/4”) Mounting Centers: 1-1/2” with oblong mounting holes See alternate photo for...

Ceramic - 9 Pin Mini Tube Socket (solder)

Ceramic tube socket commonly used for preamp tubes or EL84 power tubes. Chassis hole: 7/8” Mounting Centers: 1-1/8” Bottom or top mount See alternate photo for dimensional drawing.

Staking Tool - For Eyelets and Turrets

Turret staking tool. Directions: Drill ⅛" hole Insert eyelet Flip board over on to a hard service Center staking tool over the eyelet Strike staking tool with hammer to clamp eyelet to board See alternate photo for dimensional drawing.

Vulcanized Fiberboard - 3" x 15" x 0.062"

Vulcanized Fiberboard, used for laying out circuits using eyelets.  NOT pre-drilled. Size: 3" x 15" x 0.062"

Turret Board - Pre-drilled 300mm x 60mm x 2mm

Blank board 300mm x 60mm, 2mm thick Glass epoxy unclad laminate.

Toggle Switch - SPST Long Arm

Carling, 2 position, On-Off, SPST with solder lugs, ½" mounting hole. 3A 250V, 6A 125V, AC/DC See alternate photo for dimensional drawing.

Switch - Carling, Toggle, SPST, Short Arm

Carling 110-63 Fender® style power and/or standby switch (SPST). This switch is a great replacement for older Fender® amps where the shorter toggle length (1/2”) is desired. 3A 250V, 6A 125V, AC/DC See alternate photo for dimensional...

Hammond 290CAZ - Power Transformer

MADE IN CANADA Replacement for Ampeg GEMINI VI 25W Equivalent to manufacturer part number PT-113 Primary: 117VAC 60Hz Secondary: 625VCT @ 100mA6.3V @ 3A Features: Designed for drop in replacement of original units, though mounting holes may...

Hammond 290CZ - Power Transformer

MADE IN CANADA Replacement for Vox AC15C1 Primary: 120/240VAC 50/60Hz Secondary: 600VCT @ 120mA25V @ 250mA6.3V @ 4A Features: Designed for drop in replacement of original units, though mounting holes may not always match up perfectly...

Hammond 261D6 - Power Transformer

MADE IN CANADA Replacement for Fender 1964 Blackface 6G15 Reverb Equivalent to Fender part number 125P24A Primary: 120VAC 60Hz Secondary: 250VCT @ 50mA6.3V @ 1.1A Output: 5-15 W Features: Designed for drop in replacement of original units...

Bone Nut - Epiphone Style (slotted)

Bone nut for Epiphone® guitars, with string slots. 1 3/4" x 1/4" x 3/8"1 3/8" string spacing Tech's notes: "Replacement nuts and saddles typically measure slightly larger than necessary to ensure a tight fit.  The extra material is easily shaped...

Unbleached Bone Nut - Slotted for Gibson

Slotted unbleached bone nut for Gibson® electric guitars. Frequently used on Les Paul guitars. 1 11/16" x 3/16" x 3/8"1 3/8" string spacing. Tech's notes: "Replacement nuts and saddles typically measure slightly larger than necessary to ensure a...

Plastic Acoustic Bass Bridge Pin - Cream

Cream plastic bridge pins for acoustic bass, with groove. 1 and 7/16 inch long, .324 inch under the collar and .312 inch at the tip. Sold individually. *Matching Cream Parts?  See our blog post regarding the frustrating truth about cream parts!

Plastic Acoustic Bass Bridge Pin - Black

Black plastic bridge pins for acoustic bass, with groove. 1 and 7/16 inch long, .324 inch under the collar and .312 inch at the tip. Sold individually.

Bone Nut - Fender Style Flat (slotted)

Slotted, Radiused Bone Nut with Flat Bottom 1 11/16" x 1/4" x 1/8".1 3/8" string spacing, 12 inch radius. Tech's notes: "Replacement nuts and saddles typically measure slightly larger than necessary to ensure a tight fit.  The extra material is...

Eminence Deltalite II 2510 - 250W 8ohm

Recommended for professional audio as a mid/hi or full-range and monitor; also for bass guitar. Works well in sealed or vented enclosures. SPECIFICATIONSNominal Diameter: 10.0", 254mmNominal Impedance: 8 ohmsPower: 250w rms, 500w programFreq...

Celestion K12H-200TC - 200W 8ohm

12" twin cone drive unit with extended high frequency response. 2" high temperature copper voice coil for increased reliability and 200Wrms (AES standard) power handling. Optimized cone neck/voice coil assembly for increased strength, minimizing high...

Black Metal Feet (Pkg 4)

Steel feet with black powder coated finish. Package of 4.  Screws not included. See alternate photo for dimensional drawing. Tech's notes: "Black powder coated glide feet doesn't seem like a good idea because the finish can rub off.  But, if...

Pole Socket - Steel for 1 3/8"

2.99" Deep Top Hat to Suit 1 3/8" Poles. Sold individually.  Screws not included. Click here to purchase the matching screws. See alternate photo for dimensional drawing.

Eminence Alpha 8A - 125W 8ohm

Recommended for professional audio mid-range applications in a sealed cabinet, or as a mid-bass in a vented satellite enclosure. SPECIFICATIONSNominal Diameter: 8", 203.2 mm Nominal Impedance: 8 ohms Power: 125w rms, 250w program Freq. Response:...