ICs & Transistors

CopperSound DIY - Cir-Kit Components (choose type)

These are the component kits only.  Breadboards sold separately (these kits work best with the "small" breadboard). Entry level component kits designed to make breadboarding fun and easy while step-by-step directions provide clear instructions...

CopperSound DIY - Substitution Box (choose type)

The CopperSound Component Substitution Boxes are a series of useful and intuitive tools to help designers easily and effortlessly select between different component values without the need to constantly remove and replace different values when trying to...

DSP Module - Accu-Bell Effector

The Accu-Bell Effector offers reverb, chorus, and delay with adjustable setting and tap tempo. This module runs on 5.5V to 9.5V DC so it is easy to incorporate into effect pedal builds. Click here to see the datasheet for an example schematic. Stereo...

IC - L78L05 Voltage Regulator 5V

The L78L05 fixed 5V regulator in a TO-92 case.  Max current 100mA. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - LM386 0.32W Audio Power Amp

The LM386 low voltage power amplifier.  Max output of 325mW @ 8 ohms. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - LM7805 L7805 Voltage Regulator 5V

The LM7805 fixed 5V regulator in a TO-220 case.  Max current 1.5A. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - NE5532

The NE5532 low noise dual op-amp (operational amplifier) JFET IC (integrated circuit). PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - NE555 Timer

The NE555 timer IC (integrated circuit).  Used in some tremolo and other modulation effects. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - NE556N Timer

The NE556N dual bipolar timer IC (integrated circuit).  Used in some tremolo and other modulation effects. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use...

IC - NJM4558

The NJM4558D (aka: JRC4558D) dual op-amp (operational amplifier) JFET IC (integrated circuit).  Identical tone to the classic 4558 found in TS circuits. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a...

IC - PT2399 Echo

The PT2399 echo/delay IC (integrated circuit) on a 16-pin DIP with a minimum of external components required. Delay time set by external resistance. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat...

IC - TC1044SCPA Voltage Regulator

Charge pump IC by Microchip Technologies. Get a higher voltage or negative voltage from a battery supply. Up to 12 V in and 12 V output. PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink. ...

IC - TL022CP

The TL022CP dual op-amp (operational amplifier) IC (integrated circuit). PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - TL061

The TL061 op-amp (operational amplifier) JFET IC (integrated circuit). PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - TL062

The TL062 dual op-amp (operational amplifier) low power JFET IC (integrated circuit). PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - TL071

The TL071 op-amp (operational amplifier) JFET IC (integrated circuit). PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - TL072

The TL072 dual op-amp (operational amplifier) JFET IC (integrated circuit). PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - TL074

The TL074 quad op-amp (operational amplifier) JFET IC (integrated circuit). PLEASE NOTE: Easily susceptible to heat damage.  If you must solder directly, always use a heat sink.  Ideally, you should use these with sockets.

IC - Xvive MN3005, BBD, 4096 Stage

The XVive MN3005 is a drop-in replacement for the original Panasonic 4096-stage MN3005 BBD chip used in many delay pedals and effects. Xvive Audio’s first-ever product was the MN3005: a re-creation of the legendary bucket brigade chip used in the...

IC - Xvive MN3007, BBD, 1024 Stage

The XVive MN3007 is a drop-in replacement for the original Panasonic 1024-stage MN3007 BBD chip used in many chorus, vibrato, and flanger pedals and effects. The MN3007 is a 1024-stage, low-noise, long-delay BBD that provides a signal delay of up to 51.2...